What four panels are included on the Design tab of the Assembly environment?

(Select one)

Fasten, Frame, Power Transmission, Spring
Bolts, Frame, Gears, Spring
Fasten, Weld, Drive, Spring
Connectors, Gears, Power Transmission, Spring

Select an answer

The Frame Generator tool only uses cross sectional shapes from the Content Center.

(Select one)

True
False

Select an answer

What are the two Hole Depth types in the Bolt Connection Generator?

(Select one)

Through All and Tapped
Blind and Counterbore
Through All and Threaded
Through All and Blind

Select an answer

The Inventor Content Center must be installed and configured for the Bolt Connection Generator to work.

(Select one)

True
False

Select an answer

What four placement options are available in the Bolt Connection Generator?

(Select one)

Linear, Nonlinear, Pattern, By Hole
Point, Edge, Pattern, By Hole
Linear, Concentric, On Point, By Hole
Linear, Circular, Sketch, Work Point

Select an answer

The Bolt Connection Generator only creates bolts, washers, and nuts. The holes must be created in the part environment.

(Select one)

True
False

Select an answer

Which of these is not one of the Bolt Connection Generator Calculators?

(Select one)

Thread pressure calculation
Bolt diameter design
Check calculation
Number of bolts design

Select an answer

You can't override the material being used for the strength calculation.

(Select one)

True
False

Select an answer

What types of geometry can be used to place frame members?

(Select one)

Edges Only
Points, Lines, Edges
Points, Lines, Faces
Edges and Faces

Select an answer

The Frame Generator tool eliminates the need for constraints between frame members.

(Select one)

True
False

Select an answer

How many different ways can the frame member be positioned relative to the input geometry?

(Select one)

9
8
2
4

Select an answer

What is the default material selected for all Frame Members?

(Select one)

Mild Steel
Generic
Aluminum
Alloy Steel

Select an answer

What end treatment tool will extend one frame members and trim the other to meet it at a 90 degree angle?

(Select one)

Lengthen/Shorten
Miter
Corner Joint
Trim/Extend

Select an answer

Only one frame member can be selected at a time while using the Trim/Extend tool.

(Select one)

True
False

Select an answer

What are the four types of Spring component generators?

(Select one)

Compression, Extension, Belleville, and Torsion
Compression, Extension, Tension, and Torsion
Compression, Extension, Linear, and Nonlinear
Compression, Frame, Power Transmission, and Fasten

Select an answer

What two inputs are required for placement of compression springs?

(Select one)

Start Plane and Diameter
Axis and Diameter
Start Plane and End Plane
Axis and Start Plane

Select an answer

Machine elements design in mechanical engineering - Quiz

Machine elements design in mechanical engineering - Quiz

What four panels are included on the Design tab of the Assembly environment?

The Frame Generator tool only uses cross sectional shapes from the Content Center.

What are the two Hole Depth types in the Bolt Connection Generator?

The Inventor Content Center must be installed and configured for the Bolt Connection Generator to work.

What four placement options are available in the Bolt Connection Generator?

The Bolt Connection Generator only creates bolts, washers, and nuts. The holes must be created in the part environment.

Which of these is not one of the Bolt Connection Generator Calculators?

You can't override the material being used for the strength calculation.

What types of geometry can be used to place frame members?

The Frame Generator tool eliminates the need for constraints between frame members.

How many different ways can the frame member be positioned relative to the input geometry?

What is the default material selected for all Frame Members?

What end treatment tool will extend one frame members and trim the other to meet it at a 90 degree angle?

Only one frame member can be selected at a time while using the Trim/Extend tool.

What are the four types of Spring component generators?

What two inputs are required for placement of compression springs?